IEC 60268-1 PDF

IEC SOUND SYSTEM EQUIPMENT – PART 1: GENERAL. Buy IEC Ed. Sound system equipment. Part 1: General from SAI Global. Buy IEC SOUND SYSTEM EQUIPMENT – GENERAL from SAI Global.

Author: Bajin Kagazil
Country: Djibouti
Language: English (Spanish)
Genre: History
Published (Last): 4 June 2007
Pages: 70
PDF File Size: 9.73 Mb
ePub File Size: 1.80 Mb
ISBN: 988-4-76752-600-2
Downloads: 91489
Price: Free* [*Free Regsitration Required]
Uploader: Taugis

Take the smart route to manage medical device compliance. We use cookies to make our website easier to use and to better understand your needs. 06268-1 may find similar items within these categories by selecting from the choices below:.

BS 6840-1:1987, IEC 60268-1:1985

Calibrate the microphones per the instructions in the Isc manual. Sound System Equipment — Part 7: The play and record acquisition takes place 3 times and the user is prompted to reposition the DUT on the HATS in between acquisitions.

You are ready to start the sequence. Click to learn more.

This sequence uses a pink noise stimulus to characterize the passive, active and total attenuation of noise cancelling headphones. Band-limited version of triangle wave is used. It consists of two pure tones: A special test signal “Program Simulation Noise”, whose spectral content is representative of music and speech.

Please ic the short form below all fields are required. This is an even-only harmonics companion of standard triangle signal. Search all 602668-1 by. Registration required The content you have requested is available only to registered visitors. The spectra are then power summed to derive a single SPL value and the Hz fundamentals are post processed to derive their SPL values. The sequence uses a stepped sine stimulus to measure frequency response, THD and impedance, a composite signal of 70 Hz and Hz with an amplitude ratio of 4: T he new audio metric allows to measure waveform degradation using music as a test signal.

  LIBRO DISCIPLINA INTELIGENTE VIDAL SCHMILL PDF

There are several unique Signal Paths used in the sequences which are not a part of the default SoundCheck installation. The folder contains dependent files required to run the sequences. It can be created by passing pink noise through a special filter network defined in IEC The data from each loop iteration is displayed as it is acquired. If the answer is Yes, the user is prompted to turn the ANC on and the sequence repeats the passive measurements.

You may experience issues viewing this site in Internet Explorer 9, 10 or If passive, connect to the headphone amp or separate audio power amplifier You are ready to start the sequence.

Please download Chrome or Firefox or view our browser tips. It then calculates the voltage required to produce 1 mW into the rated impedance. Connect the impedance boxes between the headphone amp out and headphone input.

Learn more about the cookies we use and how to change your settings.

Test Setup for measuring headphone voltage sensitivity. Headphones and Earphones is an international standard intended to characterize the performance of headphones and earphones. Calibrate the Headphone Amplifier channels per the instructions in the SoundCheck manual. A series of post-processing steps follow to apply the weighting and correction curves, calculate the LAEQ and then the Simulated Program Characteristic Voltage is calculated along with the Hz voltage sensitivity.

It can also be used to characterize the passive attenuation only of a standard non-ANC headphone. Calibrate the headphone amplifier channels per the instructions 6068-1 the SoundCheck manual.

  AEROSAFETY WORLD PDF

BS EN adds an additional requirement – that the crest factor of the test signal the ratio between the instantaneous peak level of the signal and its RMS level be between 1.

IEC | IEC Webstore

Worldwide Standards We can source any standard from anywhere in the world. The Hz recorded time waveforms are 602668-1 using heterodyne analysis to derive their fundamental values. For the purpose a new audio metric is used. No – I don’t want to receive the latest audio test information by email.

Headphone Voltage Sensitivity Final Display. Once calibrated, position the microphones 0. Your basket is empty. Accept and continue Learn more about the cookies we use and how to change your settings. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. Customers who bought this product ieec bought BS While test signals can be of any kind the measurement procedure stays the 60628-1 and waveform degradation is measured with a single parameter – Difference level dB.

IEC Headphone Test Sequences – Listen, Inc.

Five separate sequences are provided, each designed to measure specific characteristics. Germain – What You Think About Find Similar Items This product falls into the following categories. Crosstalk and radiation curves are then shown on the final display.