DIN EN 10216-2 PDF

Buy DIN EN SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES – TECHNICAL DELIVERY CONDITIONS – PART 2. DIN EN Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 2: Non-alloy and alloy steel tubes with specified elevated. ​Manufacturing program with average wall thickness (EN ). Vallourec supplies seamless steel tubes for pressure purposes in accordance with.

Author: Gardaramar Nikasa
Country: Andorra
Language: English (Spanish)
Genre: Life
Published (Last): 16 February 2018
Pages: 139
PDF File Size: 2.92 Mb
ePub File Size: 19.25 Mb
ISBN: 802-4-63187-719-1
Downloads: 16003
Price: Free* [*Free Regsitration Required]
Uploader: Dolkis

The tubes shall be delivered with bevelled ends see figure 1. ENMetallic products – Types of inspection documents. Carbon and low-alloy steels ISO Impact testing see table 4.

Set of dimensions other than D and T see 8. All dressed areas shall blend smoothly into the contour of the tube. Stainless steel tubes; German version EN For undated references, the latest edition of the publication referred to applies. Standards Subsctiption may be the perfect solution. Automatic electromagnetic testing of seamless and welded except 102116-2 arc welded ferromagnetic steel tubes for verification of hydraulic leak tightness. Page 7 EN If not agreed otherwise, 1 sample per one ladle and in dih size or 1 sample per one ladle and annealing without thermal processing.

Site map News Contact. After fracture the test pieces shall not show any visible cracks without the use of magnifying aids excluding the fracture point. Already Subscribed to this document. The choice of a suitable physical or chemical analytical method for the analysis shall be at the discretion of the manufacturer. At the manufacturer’s discretion: Please first log in with a verified email before subscribing to alerts. When an inspection document 3.

  ALESIS NANOVERB 2 MANUAL PDF

The qualification shall be in accordance with EN or, at least, equivalent to it. Sn is the manufacturer’s mark; TC1 is the designation of the test category 1; Y is the cast number or a code number; Z1 is the mark of the inspection representative; Z2 is the identification number. Rohre aus legierten und unlegierten Sthlen mit festgelegten Eigenschaften bei erhhten Temperaturen enthlt nderung A1: Welded steel tubes for pressure purposes — Technical delivery conditions — Part 1: Mechanical properties of seamless steel pipes for elevated temperatures tested in room temperature.

Upper yield limit or yield strength Re or R0,2 for wall thickness of t min. ENGeneral technical delivery requirements for steel and iron products.

Tubular Products (EN 10216-2)

Standards Subscriptions from 102116-2 provides a money-saving, multi-user solution for accessing standards. Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 2: Unless option 7 is specified, the choice of the test method is at the discretion of the manufacturer. Page 30 EN Automatic full peripheral ultrasonic testing of seamless and welded except submerged arc welded steel tubes for the detection of longitudinal imperfections.

Unless option 15 is specified the wall thickness shall be measured at both tube ends.

All tubes except group A. One of the inspection documents 3. Test pressure for hydrostatic leak tightness test see Page 28 EN Where test pieces of least 5 mm width cannot be obtained, the tubes shall not be subjected to impact testing.

Steel names, principle symbols.

ENDesignation systems for steels – Part 2: Proof strength Rp0,2 shall be verified. However, slight incipient cracks at its edges shall not be regarded as justification for rejection. Special ends preparation see 8. Until this document is published as a European Standard, the corresponding national 102162 s should be agreed at the time of ordering. English price group 16 www. Boiler tubes are used in heat exchange appliances in which the energy is transferred from one fin to the other.

  ELEKTOR AVRIL 2011 PDF

In addition, the general technical delivery requirements specified in EN shall apply. Non-alloy steel tubes with specified room temperature properties This Part of EN specifies the technical delivery conditions for two qualities TR1 and TR2 of welded tubes of circular cross section, made of non-alloy quality steel and dun specified room tempe….

List of standards Mass calculator Fundusze europejskie.

Description of DIN EN and | Sunny Steel Enterprise Ltd.

Preferred outside diameters and wall thicknesses have been selected from ENV and are given in table 6. The ends shall be free from excessive burrs.

Additional marking, as agreed upon at the time of ordering, shall be applied. Pipes with precise lengths are manufactured with the following tolerance values: Wall thickness measurement away from the ends see Unless option 1 is specified, the tubes may be either hot or cold finished at the discretion of the manufacturer. Boiler tubes Boiler tubes are used in heat exchange appliances in which e energy is transferred from one medium to the other.