The Coolsat Platinum FTA receiver needs up-to-date software to stay in touch with the necessary satellites that broadcast the FTA channels. FTA or. Find great deals on eBay for coolsat manual. DREAMLINK T4 T5 LITE COOLSAT HD KBOX Remote Control w/Batteries. Coolsat Manual. Here is a little manual I created from various forums. Hope you like it! Attached Thumbnails. Ya Can’t Play with a Broken.
|Country:||United Arab Emirates|
|Published (Last):||12 December 2018|
|PDF File Size:||11.28 Mb|
|ePub File Size:||20.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
After setting the antenna settings you can now return to loading the channel list if your prefer to load a custom channel list. Since TP 1 R for is a spot beam transponder, many did not receive any signal strength or signal quality for on TP 1 because they coilsat not in the regional spot beam. Repeat the process by going to the next transponder you want to add by clicking on the green button, and continue for all transponders 500 wish to add until you have finished.
Use the Lyngsat chart http: The Legacy SW should remain Off as this function is intended to be used with external SW switches instead of a diseqc switch used to switch between dishes using single lnbs.
I have freestanding Series 8 dishwasher. The following are some illustrations of the scan modes. I strongly advise and warn you not to flash channel lists to the default channel bin as this feature is now filled with satellite data information required by the EPG software which is loaded with the bin flash.
When asked for password, enter This will open the transponder edit window, where you can enter the new frequency, symbol rate and vertical polarity. Want Answer 0 Clicking this will make more experts see the question and we will remind you when it gets answered.
Regardless of the switch setting, satellite identification will come from the signal received. Do not turn receiver on with front power button. Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
This is up to your personal taste. An RS port is located on the rear of the Coolsat Platinum to allow users to program the receiver with mahual latest software. Channel Master offers several channel renaming and ordering options. What is a PID? Be sure to turn the Sid Sort option off if you cpolsat to use a custom channel list.
It is noted that the N1 key lines can be used by entering the entire 32 bytes of the active key in key lines 00 and 01 although 500 is not recommended with N2 encryption. Press ok and device and then enter code to do manual search push ok device at the same time light will blink twice then keep pushing up on the channel button until tv shuts off then push ok then you are done i hope this helps.
Download all files and unzip them and place them in a handy place where you can locate them.
Here’s a link to this great service Good luck! After clicking on the Channels Tab, the tool will open in the default setting normally used to load the channel list to the receiver. Turn off the receiver with the front button or remote and manually turn off power to the receiver with the rear power switch button before making any disconnects of cable in and cable out from the receiver. You will be ready to flash your custom channel list after you have completed doing a factory reset, reset your antenna settings, turned off the Sort By Sid Option and after you have reconnected to your personal computer: He wrote news articles and independently authored op-ed columns for the on-campus newspaper, “The Signal” and had articles published in “Garden State Surf Magazine.
Be sure to do Firmware first if you are going to do a complete copy of Firmware and Channel Data. Treat the DP34 the same as an external diseqc switch and run a cable from each lnb as set out above for making cable connections when using more than two lnbs. Before going any further, it is noted this Manual is not intended to be a Noobie Guide to the general universal applications used in FTA Receiver testing but only as a guide to using the Coolsat Receiver assuming the Tester has some basic understanding of setting up and pointing the dish and how to route the signal from the lnb to the receiver with switches and setting the signal path in the Dish Setting Window for each satellite in the receiver.
Ontransponder 1 is a spot beam transponder and many of you will 9 not get a signal on Transponder 1. Brief Note Concerning N2 Keys: Plug into wall outlet. By default, the loader tool will open in Software tab with receiver selected. For Dishpro type lnbs, Twin or Quad, no external switch is needed.
A prior work around has always been to delete transponder 1 off any custom channel list or to set your antenna settings as you think it should be and then enter the Motorized Dish setting in Installation and scroll to Echo 7 satellite and then scroll down to transponder and scroll up through transponders to verify signal for Echo 7.
Upload your list to the personal computer by using the Coolsat Pro Loader Manuao. The tool by default will open in the software flash mode used to flash the bin file to the receiver. The following is an illustration of the Edit Channels window.
In the present configuration for N2, we now see key lines 10 and 11 holding the 32 byte idea 0 key and key lines 20 and 21 holding the 32 byte Idea key 1.
Or you can press OK and it will open a keyboard selection type menu to enter keys. The Finish window will show the prior version of bin loaded. Many people are walking around not understanding the difference between the old N1 keys and the new N2 keys amnual being used and where proper placement of the keys go into the CAS key lines.
Coolsat Receiver Testing Manual |
The Legacy SW function can be used to cascade switches. Select satellite with left or right volume buttons to locate your satellite, when found, scroll down and set antenna settings using left or right volume buttons to make each selection all the way down the settings.
The brightness, contrast and color of the on screen video display can now be adjusted via the remote by using the Yellow button located to the Left of the Multi Manjal Blue button. Click on Connect and let it finish. If you choose to use a custom channel list, you must make sure the satellite names are the same as used in the default list for EPG to work correct.
I would recommend not using the Coolsat Channel option of coolsag loader as this function is needed by 500 bin software to operate the EPG program correctly. To re-enable the lock, the receiver must be turned off.
As before, usually we will see one key active and the other inactive although we have seen instances where dish was running two active key strings at one time with the N2 encryption.
Use a null modem cable and connect the two units. When you have browsed in the file you want to flash to the receiver, click on the Connect Button. Most satellites use a base address of but some satellites use a different base address.
Coolsat Platinum FTA Digital Satellite Receiver Silver Remote Working | eBay
Feb 27, Jensen Remote Control. These options are self explanatory and are shown on the following illustration. Let it finish and save and then move on to the next satellite you want to scan.